
Laser cutting machines are efficient and precise processing equipment, but if safety operating procedures are not followed during use, serious safety accidents may occur. The following are safety operating procedures for laser cutting machines sorted out based on search results.
1. Inspection of safety facilities
Before using the laser cutting machine, it is necessary to carefully check whether the various safety facilities of the machine are operating normally. All safety devices must be able to operate safely and reliably.
1. Main and auxiliary controllers: The main and auxiliary controllers must be firmly fixed. During operation, be sure not to allow the four support columns to deviate. At the same time, check whether the controller circuit is intact and whether the connection terminals are in good contact.
2. Emergency stop device: The emergency stop device must be tested daily to check whether it functions properly. At the same time, check whether the button contact is reliable and whether the laser power supply can be quickly cut off to ensure that in an emergency, the power supply can be quickly cut off and the laser radiation can be stopped.
3. Photoelectric protection device: In order to ensure the safety of the operator, the laser cutting machine must be equipped with a photoelectric protection device. Its range and position must be accurately measured and calculated. In the event of a photoelectric protection device failure, it must be repaired in a timely manner.
2. Safety precautions during operation
When operating a laser cutting machine, you must strictly abide by the safety operating procedures. The precautions are as follows:
1. Wear protective equipment: When operating a laser cutting machine, you must wear appropriate protective equipment. Protective equipment must be intact, and at the same time avoid wear and damage, and avoid interference from external factors.
2. Ensure the safety of the operating environment: The operating environment must be dry and clean, and avoid excessive relative humidity, which may cause various faults that may exist during machine operation. During operation, there must be no dangerous substances such as flammable particulate matter and flammable gases around. During the operation of the laser cutting machine, a dedicated person must be responsible for supervision.
3. Stay alert during operation: The operator must stay alert and be alert to the surrounding situation to ensure safety. Even if a minor fault occurs, the machine should be stopped for maintenance in time to prevent serious accidents.
4. Avoid excessive fatigue: Continuous operation of the laser cutting machine for a long time will cause the operator to have a certain degree of fatigue. At this time, the machine should be stopped for a period of time to ensure that there are no errors in subsequent operations.
5. Laser radiation hazards: Laser radiation can cause harm to the human body, so operators must strictly follow laser protection regulations. Do not put your hands into the light path to prevent the laser from hitting people. And a safety window that absorbs laser radiation should be installed on the operating table to reduce the harm of laser radiation to people.
III. Design and installation of workpieces
Before operating laser cutting, you also need to consider the design and installation of the workpiece to ensure the safety and processing quality of the workpiece.
1. Design of workpieces: The design of the workpiece must meet the working requirements of the laser cutting machine, and overly complex parts cannot be designed. Because in the design process, you must also pay attention to choosing the right materials to avoid the materials being too fragile.
2. Installation of workpieces: The installation of workpieces is also very important. It is necessary to ensure that the workpiece is balanced and stable, and that its contact surface with the machine is flat. In addition, appropriate fixtures should be added between the workpiece and the laser cutting machine.
IV. Maintenance and care
Regular maintenance and care can ensure the normal operation of the laser cutting machine and the safety of the operator.
1. Daily maintenance: Daily maintenance includes cleaning the machine, checking optical components, lines, adjusting key components, etc. For each maintenance point, standard operations and procedures must be strictly followed and relevant records must be kept.
2. Periodic maintenance: Periodic maintenance is also very important. The laser cutting machine must be overhauled and maintained to ensure the performance, accuracy and life of the equipment.
V. Follow-up work
The follow-up work of the laser cutting machine includes sorting and keeping relevant materials, completing case reports, sorting maintenance records, and participating in training. These tasks must be standardized and rigorous to ensure the smooth use of the laser cutting machine.
VI. Summary
The use of the laser cutting machine must strictly comply with the above safety operating procedures and overcome all safety hazards to achieve the best use of the machine. At the same time, each laser cutting machine must receive relevant safety training and actual operation assessment before use to ensure that the machine can work safely and stably.
